Reman Sitrak G7S 6×4 Tractor Truck
Built on original Sinotruk Sitrak G7S platform, this reman camion Sitrak rejects patch‑style repair work. REMAN ROAD reman workflow eliminates invisible metal fatigue accumulated from high‑load operation, recalibrates powertrain output and chassis geometric tolerance.
Reman Sitrak G7S Tractor Truck Description
- This reman Sitrak camion unlocks second‑life high‑value utilization for these proven assets, strictly following REMAN ROAD unified reman quality control framework.
- Every reman camion Sitrak goes through structured stages: pre‑reman asset qualification screening, full teardown & precision cleaning, component grading & renewal, powertrain bench calibration, chassis structural restoration, whole‑vehicle reassembly with OEM‑standard torque control, multi‑dimension performance validation and document archiving.






Technical Parameter Table
- Model: Chinese Reman Sitrak G7S Tractor Truck 6×4
- Cabin: H78L high‑roof sleeper cab, reman refurbished interior
- Engine: Remanufactured MC11 series diesel engine
- Transmission: Remanufactured HW19712CL, 12‑speed manual gearbox
- Front Axle: H153 remanufactured steering front axle
- Rear Drive Axle: Reman heavy‑duty double reduction axle
- Suspension System: Reman restored leaf‑spring suspension, renewed shock absorbers
- Brake System: Full reman air brake system, hydraulic retarder retained
- Fifth‑Wheel: 90 mm standard coupling fifth wheel
- Frame Condition: NDT inspected, deformation corrected within reman repair limit
- Fuel Tank: Cleaned & pressure tested fuel tank, check for corrosion and leakage
- Tire Configuration: 12R22.5 heavy‑load radial tires
- Traceability: Complete reman inspection, component‑replacement & test archive available
Chassis Frame & Running Gear Reman Restoration
- Perform full frame inspection: thickness detection, crack scanning, deformation measurement on main beam and cross‑members.
- Conduct qualified cold straightening for frame deformation within repair limit; reject frames exceeding engineering repair threshold.
- Fully disassemble suspension groups, steering assemblies and drive axles; renew all aging rubber bushings, shock absorbers, bearing assemblies and sealing parts.
- Recalibrate axle gear meshing tolerance, eliminate abnormal transmission noise and hidden wear risk.
- Complete full chassis geometric calibration, restore wheelbase, camber and caster angle back to factory specification, avoid tire partial wear and uneven load distribution.
Full‑Vehicle System Renewal: Brake, Electrical & Auxiliary Systems
- Dismantle and inspect the whole‑vehicle brake system, replace aging air chambers, sealing elements and worn valve components, test brake response and pressure holding performance.
- Sort out whole‑vehicle wiring harness, eliminate aging insulation, damaged connectors and hidden circuit faults. Replace degraded sensors and control modules.
- Renew cooling system assemblies including water tank, pipelines and sealing gaskets, verify heat‑dissipation performance under simulated high‑load working condition.
- Reassemble every auxiliary component following standardized torque requirement, avoid assembly‑caused hidden failures common in casual repair workshops.
RFQ
- Q1: What is the biggest difference between your reman Sitrak camion and an overhauled used tractor?
A: Overhaul mainly fixes existing visible faults, cannot remove invisible metal fatigue accumulated over service time, and only extends residual asset life. Our standardized reman completes full disassembly, full non‑destructive inspection, component renewal and system calibration, realizing asset‑life‑reset to near‑new performance and starting a brand‑new lifecycle baseline. - Q2: How do you confirm whether a Sitrak C7H base truck is qualified to enter remanufacturing?
A: We conduct multi‑dimensional incoming screening. Units with severe collision damage, irreparable frame cracks or permanent thermal damage to engine block will be eliminated. We combine NDT scanning, dimension measurement and historical working‑condition review to judge reman feasibility before production. - Q3: Does reman Sitrak camion have the same service life expectation as a brand‑new truck?
A: After standardized reman asset‑life reset, its predictable usable service cycle is close to new‑vehicle level for heavy‑transport working‑conditions. It should be noted reman cannot achieve 100% identical lifespan as brand‑new unit for every detail; all performance indexes follow our published reman benchmark standard. - Q4: Which core components will definitely be replaced during reman camion Sitrak workflow?
A: All time‑limited consumable and friction components get replaced, including bearing sets, piston rings, all sealing gaskets, rubber bushings, shock absorbers, aging sensors and wiring harness damaged sections. Reusable metal base parts pass strict fatigue inspection before reuse. - Q5: Will reman work change the original OEM structural design of Sitrak C7H?
A: Genuine reman follows original Sinotruk factory design specification. We restore rather than modify core structure. No arbitrary structural modification will be applied during reman process to guarantee original vehicle safety design. - Q6: What test items will this Chinese reman Sitrak tractor truck finish before delivery?
A: It includes engine dynamometer load test, chassis geometry calibration, brake‑system pressure holding test, whole‑vehicle electrical function verification, simulated‑load road simulation test. Every test result is recorded in traceability archive. - Q7: Can I use Chinese reman Sitrak tractor truck data for enterprise ESG and carbon‑reduction accounting?
A: Yes. Every REMAN ROAD reman Sitrak camion keeps full workflow records. Remanufacturing greatly cuts carbon emission compared to new‑truck production. These documented records can provide supporting material for your ESG assessment.




